Providing and application of vacuum in a laboratory

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1

Introduction
P2Os7fBG3M

Vacuum supply is usually an integral part of planning for laboratories in public or private buildings. It is more complex than other piped utilities because the requirements for vacuum technology are different in a synthesis laboratory than, for example, in an analytical or cell biology laboratory. These different requirements cannot be met with the same vacuum supply. To address the need for vacuum supply tailored to the applications, the specific requirements should be clarified early in the planning phase. “The right tool saves time” is an old saying of craftsmen that applies to the vacuum supplied to each laboratory. Whether because vacuum is poorly understood because the piping systems seem so similar to piped gases, or because traditional practice has dictated a single building-wide system, the unique requirements of vacuum supply are frequently overlooked in the lab planning process. Nonetheless, for many applications, tailored vacuum is invaluable. Appropriate vacuum allows the chemists to achieve desired results faster, more safely, more conveniently and also reproducible. This topic is intended to be an initial orientation for small laboratory planners, underground chemists and drug manufacturers to the important consideration in planning vacuum supply for laboratories.

What is the vacuum?

Vacuum as used in the laboratory is simply pressure below atmospheric pressure. The essential qualities of the vacuum that determine its usefulness in any particular laboratory application are the depth of vacuum – how much below atmospheric pressure and the pumping speed, that is, how quickly can air, vapors or gases be removed from the vessel being evacuated.

Application

Many chemists use vacuum every day. But how do they use it? Vacuum is used for many standard applications in the preparation and processing of synthesis products. In most cases, the vacuum is not the focus, but plays an essential supporting role. The most familiar lab vacuum applications are filtration and drying. Of course, you could filter without vacuum - like brewing coffee - by letting gravity do the work for you. The problem is that, in the laboratory, the process often proves to be too slow due to the broad spectrum of solvents and solid substances. To speed up the process, low-pressure – i.e., vacuum – is created in a filter flask (Büchner flask) for Suction (vacuum) filtration.
Te0pVM5lIU
WyN5RdLZlv

Filtration with the aid of a chemical-resistant vacuum pump

In a drying process, on the other hand, the goal is to change the state of a sample from liquid to gaseous. We could simply allow drying to happen, just as we air-dry laundry. As with filtration, this process would also take too much time, so a vacuum is used here as well to accelerate the process with help of Vacuum desiccators. Heat could be used to accomplish the same effect, but by decreasing the pressure level, less heat energy is necessary to evaporate solvents. Thus, use of vacuum makes possible the efficient drying of heat-sensitive sample materials.
JblZAGjXzs
3i4xe7DPyL
Vacuum applications used in laboratories vary with the scientific discipline, and the different applications have distinct vacuum requirements. Filtration is a process used in nearly all laboratories. Synthetic laboratories in which produce some solid (meth, amph, mephedrone, MDMA and etc) commonly use vacuum for drying. These applications all require vacuum in the “rough vacuum” range – between 1 and 1000 mbar.
HqBz6a87fG
In chemistry laboratories, numerous vacuum-driven technologies are used for evaporative separation of mixtures of substances such as solvents. The best known example of this is Rotary evaporation, for which the precise control and pressure regulation impose significant requirements regarding to pump and control technology in the rough vacuum range. This equipment allows evaporating solvents quickly without intensive heating, also you can recuperate solvents after synthesis from waste.
CTrY95U8CZ
BgnVfPIOFx

In contrast, Schlenk line and Vacuum distillation, also common in chemistry labs, demand vacuum in the fine vacuum range. This technique is used when the boiling point of the desired compound is difficult to achieve or will cause the compound to decompose. Reduced pressures decrease the boiling point of compounds.
QV4GBUHgFA
T28hQ309ZK

Pumps

Diaphragm
Diaphragm pumps use a flexible diaphragm and a set of check valves to produce pumping pressure and typically produce low to medium vac. They are frequently resistant to solvent and mildly corrosive vapors, making them useful for rotary evaporators, but their inability to produce high vacuum limits their utility. Diaphragm pumps often do not require oil. This type of pump may produce to 1.5 mbar vacuum. Main disadvantage is a produced noise to 50-60 dB and necessity of periodic maintenance (replacement of oil and membranes). Diaphragm pumps have cost from ~450-$500.
5mnY7wsHFt
Mik0sE7ec3
Rotary Vane
Rotary-vane pumps are also a common type of vacuum pump, with two-stage pumps able to reach pressures well below 10−6 bar. Rotary vane pumps use rotating sets of circular vanes in an elliptical cavity to create pumping pressure, and can achieve medium to high vacuum. If your pump requires oil changes, it is likely a rotary vane pump. Though they can achieve higher vacuum than diaphragm pumps, they are easily damaged by solvent or corrosive vapors. Steps must be taken to prevent harmful vapors from reaching this type of pump, such as the implementation of a cold trap, as contamination can significantly reduce a pump's efficiency and lifetime. Approximate cost from 150-$200.
UvdYFz9MyK
Tb0C2Dd9lc
Water jet pump
The water jet pump is a propellant jet pump in which water flows through a nozzle. A vacuum develops as a result of the high flow rate. The final vacuum to be reached depends on the water pressure and temperature (for water, 3.2 kPa or 0.46 psi or 32 mbar at 25 °C or 77 °F). If not considering the source of the working fluid, vacuum ejectors can be significantly more compact than a self-powered vacuum pump of the same capacity. Approximate cost ~25-$30. The lower the intake pressure, the more the suction capacity declines. Water jet pumps are distinguished by their very low acquisition costs and corrosion resistance. However, they are stationary. To use them, water and wastewater connections must be mounted on laboratory tables and in exhaust hoods. Because of the typical water consumption of several hundred liters per hour - a hundred thousand liters per year, even with moderate use – the water jet pumps generate high operating costs for fresh water and wastewater. Another drawback is the high noise level and the poor environmental compatibility, since all substances and solvent vapors pumped from applications go into wastewater.
9BpGm0gnjU
M5gYJwLcyh
BDaWOj1INK

Vacuum pump selection

In underground chemistry laboratory, vacuum is among the basic equipment for laboratory workstations. Consequently, vacuum supply is already an integral part of the planning of new laboratories, since it is needed for many applications - whether evaporation, distillation, drying or simply aspiration or filtration. These rough vacuum applications are best served by chemistry diaphragm pumps.

Safety

Care should be used to avoid venting harmful vapors into the lab atmosphere. Pump exhaust should be either vented into a fume hood, or fitted with an appropriate scrubber or filter. When broken, evacuated glassware shatters and violently implodes, sending fragments flying at high velocity. Inspect your glassware for cracks and flaws before applying vacuum.
 
Last edited:

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
Hi Patton, another great and extensive explanation. Thank you
 

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
I have an oil-pump and the main concern is cold trap, not to get vapours in the pump, what do you recommend for small-medium scale lab? The prices vary so much and I`m not sure what would be sufficient enough. I was even thinking that I could get a condenser set up as a cold trap as the cheapest solution. The air would flow where normally the cooling water flows and I would circulate ice-cold water in the middle, but this probably would not work.
 

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
Also, how to set up some kind of regulator to make the vacuum constant? If I have the pump on all the time, it is too much and the machine will not manage, if I switch it off the vacuum drops. I was thinking that some kind of gauge/meter could switch the pump on an off in a range of vacuum ideal for that purpose. Sorry if my questions are stupid again.
 

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1
Hi, thanks for the feedback! I recommend to use 3rd trap (with bottom tap on pic below). I've used this one with oil vacuum pump.
9xPoGRDNby
JMIHQsrFyv

When preparing the coolant inside the dewar, add the dry ice or another cooling agent like salt ice slowly to the liquid portion; this will avoid foaming. Dry ice coolants should always be open to the atmosphere, as a closed system will cause dangerous pressure build-up. Carefully lower the trap into the dewar. If running the vacuum for long periods (30+ minutes) you may need continually to add more dry ice. Check the trap often to ensure that the collected liquid does not freeze and cause a blockage of the trap. If this occurs, you may need to switch your coolant to a higher temperature bath (e.g. ice and salt bath). When complete, remove the trap from the dewar, shut off the vacuum and slowly vent.​
 
Last edited by a moderator:

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1
I know one system, but I can't find it right now. Give me more time. I'll find it.
 
Last edited by a moderator:

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
Thank you ever so much Patton, what is the size of the cold trap I should be looking at? Another (perhaps very nube) question is whether I should use some kind of vacuum regulator to keep the vacuum in a certain range? The pump`s intructions say I should not run it for more than 30 minutes at a time and I`m also concerned about the vacuum being too deep, leading to excessive bubbling which could create trapped water in the distillate (that`s how I imagine - perhaps unfounded). Is there any video you`d recommend to watch where I can see how this is done in practice with a rotary vane pump and a cold trap. So far I have been super cautious only creating vacuum in chambers and using this for the distillation, but I know this is nowhere near ideal and not so efficient at all.
 

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
The size of the cold trap is a big question as well, because the prices vary a great deal.
 

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
This would be great. I reckon there should be some modifications.
 

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1
You can take standard size for rotavap machine. In case of big volume of evaporation solvent flask, you can use two traps sequentially. It depends on volume.
 
Last edited by a moderator:

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
Is it true that without such regulator vacuum is more difficult to use when dealing with highly volatile substances (such as acetone). I found it way easier to just distill acetone without vacuum using boiling stones it is smooth and quick anyway, while with the vacuum on, the temperatuer was fluctuating, big bubbles, too much vacuum etc. Equlibrar is a great company by the way they seem to have regulator for the single/small user as well, I will request a qute whether it is affordable or not? Do I interpret your post correctly that you more or less recommend diaphragm pump for the average user? It seems to be much less hussle than anything else.
 

diogenes

Don't buy from me
Resident
Language
🇬🇧
Joined
Dec 27, 2021
Messages
183
Reaction score
98
Points
28
Sorry if this is very basic, but how do I get dry ice, how can I keep it at such a low temperature?
 

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1
Yes, you are right
You have to buy, it cannot be produced at home, and keep in Dewar vessel
 

Jack

Don't buy from me
Resident
Joined
Oct 24, 2021
Messages
53
Reaction score
18
Points
8
Is it acceptable if the internal diameter of the tubing from the vacuum pump to the distillation apparatus is 6mm. 15 micron ultimate vacuum 45L/min.
 

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1
15 microns is extremely deep vacuum. You don't need so hard vacuum for distillation.
I think yes, be careful with so deep vacuum.

P.S. Answer me with "Reply" function, I'll see note.
 
Last edited by a moderator:

ASheSChem

Don't buy from me
Resident
Language
🇫🇷
Joined
Apr 10, 2022
Messages
300
Reaction score
168
Points
43
this kind of pump is ok ?
OTZjyiocm9
IuOZD3IBkj
 

G.Patton

Expert
Joined
Jul 5, 2021
Messages
2,704
Solutions
3
Reaction score
2,845
Points
113
Deals
1
for what?
 

ASheSChem

Don't buy from me
Resident
Language
🇫🇷
Joined
Apr 10, 2022
Messages
300
Reaction score
168
Points
43
sory; for vacuum filtration with a buchner filter
 
Top