Need help with making 5F-ADB E-liquid
- Thread starter mynameisunkown
- Start date
Here is a short guide I made a while back but for 5cl (which is same because they are very similar potency). Except the doses may be a little weak in this guide, but start small to be safe:
HOW TO MAKE VAPE SOLUTIONS FOR VAPING WITH RAW POWDER:
Considering about 4 drags of an average power vape will equal around 1 drop of solution, if you take 4 hits of a 250ug/drop solution you will consume about 0.25mg 5cl-adba (about the active dose, maybe a bit potent for a user with no tolerance. Make sure you don't take a bunch of quick hits in succession thinking it's not hitting. Seen many of ODs happen this way! Just take a couple drags, wait a couple minutes (2-3m) to see where you're at, then re-dose a drag or two and repeat the waiting until you're at a level that's just right for you. BE SAFE! I always recommend using a graduated cylinder and a good scale so you know the exact concentration and therefore the exact dose you are consuming. Always start with the lowest concentration possible if you are inexperienced with noids!
So for example to make the 250ug per drop of vape solution (a drop = apprx 1ml) you will weigh out 250mg powder and break into as fine of chunks as possible for quickest dissolving time. Then measure out 50ml vape solution or pg/vg with flavoring. Add the raw powder into the vape solution and stir really well or shake. TIP: if you want the powder to dissolve faster, you can heat up your vape solution a little bit before in the microwave or on a hotplate BEFORE adding the powder, then stirring thoroughly upon addition until no more visible powder remains and the vape liquid is clear. You will want to use one of those oral syringes with a needle or a dropper bottle (or just use the vape juice bottle you buy your vape juice in) and squeeze some into your tank of choice
Considering about 4 drags of an avg power vape will equal around 1 drop of solution, if you take 4 hits of a 250ug/drop solution you will consume about 0.25mg 5cl-adba (about the active dose, maybe slightly potent for a user with no tolerance. Make sure you don't take a bunch of quick hits in succession thinking it's not hitting. Seen many of ODs happen this way! Just take a couple drags, wait a couple minutes (2-3m) to see where you're at, then redose a drag or two and repeat the waiting until you're at a level that's just right for you. BE SAFE! I always recommend using a graduated cylinder and a good scale so you know the exact concentration and therefore the exact dose you are consuming. Always start with the lowest concentration possible if you are inexperienced with noids!
HOW TO MAKE VAPE SOLUTIONS FOR VAPING WITH RAW POWDER:
Considering about 4 drags of an average power vape will equal around 1 drop of solution, if you take 4 hits of a 250ug/drop solution you will consume about 0.25mg 5cl-adba (about the active dose, maybe a bit potent for a user with no tolerance. Make sure you don't take a bunch of quick hits in succession thinking it's not hitting. Seen many of ODs happen this way! Just take a couple drags, wait a couple minutes (2-3m) to see where you're at, then re-dose a drag or two and repeat the waiting until you're at a level that's just right for you. BE SAFE! I always recommend using a graduated cylinder and a good scale so you know the exact concentration and therefore the exact dose you are consuming. Always start with the lowest concentration possible if you are inexperienced with noids!
So for example to make the 250ug per drop of vape solution (a drop = apprx 1ml) you will weigh out 250mg powder and break into as fine of chunks as possible for quickest dissolving time. Then measure out 50ml vape solution or pg/vg with flavoring. Add the raw powder into the vape solution and stir really well or shake. TIP: if you want the powder to dissolve faster, you can heat up your vape solution a little bit before in the microwave or on a hotplate BEFORE adding the powder, then stirring thoroughly upon addition until no more visible powder remains and the vape liquid is clear. You will want to use one of those oral syringes with a needle or a dropper bottle (or just use the vape juice bottle you buy your vape juice in) and squeeze some into your tank of choice
Considering about 4 drags of an avg power vape will equal around 1 drop of solution, if you take 4 hits of a 250ug/drop solution you will consume about 0.25mg 5cl-adba (about the active dose, maybe slightly potent for a user with no tolerance. Make sure you don't take a bunch of quick hits in succession thinking it's not hitting. Seen many of ODs happen this way! Just take a couple drags, wait a couple minutes (2-3m) to see where you're at, then redose a drag or two and repeat the waiting until you're at a level that's just right for you. BE SAFE! I always recommend using a graduated cylinder and a good scale so you know the exact concentration and therefore the exact dose you are consuming. Always start with the lowest concentration possible if you are inexperienced with noids!