Metamfetaminsyntese fra efedrin ved hjælp af I2 og H3PO2

[hacke8]

Mine herrer, jeg lavede dette eksperiment, og jeg opvarmede det til 125 grader, fordi fosforsyre opvarmes til 130 grader, vil der være fosfatbrintgas (giftig). Er der nogen måde at undgå dette på?

 

[GhostChemist]

du kan bruge absorptionen af PH3 med NaClO og NaOH
H3PO2 ødelægges ved 170 C

 

[CARLITOBRO]

kan jeg bruge hydriodic acid 57% i stedet for hypophosphorus acid? venligst gentag

 

[caydiantak]

Fungerer dette med pseudo?

 

[Toti]

Hej, er der nogen forskel, hvis jeg bruger sudoephedrin i denne opskrift?
Tak skal du have

 

[Throw-off]

Forskellige forhold for efedrin og pseudo.

 

[amieri]

Du vil have en molær ækvivalent, disse er hypotetiske mængder, men siger, at 6 g efedrin er 20 mmol af en mol efedrin, så vil du have 20 mmol ækvivalent af pseudo.im på ingen måde en pro og har aldrig engang slået molekylvægten op for nogen af dem, der sætter det er ideen.
Der er et indlæg her et eller andet sted, jeg tror fra patten, der er meget detaljeret og informativ om emnet, absolut se det op, fordi dette er noget, der er meget vigtigt i alle reaktioner.
Med venlig hilsen B

FÅ AMERIKA TIL AT LAVE MAD IGEN!

 

[kackbratze]

Hej, jeg har et spørgsmål: Kan man bruge kaliumjod i stedet for jod? Fordi kaliumjod er meget lettere at købe.

 

[G.Patton]

Hallo, nej. Disse stoffer har forskellige kemiske egenskaber.

 

[Throw-off]

Du kan bruge pottasiumjod til at lave jod. Det kan gøres på en doven søndag eftermiddag.

 

[waltjr5858]

It can be done in about 20 minutes

 

[CARLITOBRO]

kan jeg bruge hydriodic acid 57% i stedet for hypophosphorus acid? venligst gentag

 

[G.Patton]

Hej, nej, du kan hverken bruge hydroiodic acid eller phosphorous acid

 

[Bmth]

Spørg eksperter om svar, for jeg har fejlet og brugt en masse penge og materialer.
Bahasa Indonesia:Hvad er der brug for til den næste proces i dette destillationsstadie?
Bahasa Indonesia:Om resultatet af destillationsdampen eller resten af det materiale, der opvarmesOm resultatet af destillationsdampen eller resten af det materiale, der opvarmes

 

[William Dampier]

Your photo has a very high distillation temperature for dcm

 

[Pinkbay]

Lærer, kan jeg bruge DCM i stedet uden destillation og gå direkte ind i den overvægtige hydrogenchlorid?

 

[William Dampier]

You can do this, but it is better to extract into the water layer when acidification and evaporate part of the water. You can use aq. HCl

 

[Saâd]

Hello, please can you give the weights that can be followed with the steps to get one kilogram ?

 

[William Dampier]

You must control the boiling to avoid problems with the volcano. Use boiling chips. Change the weight you need according to the specified proportions.

 

[cicici]

Hello, I have a question
I got a good result through this work
I have a few questions
1. It was heated to 100 degrees in hypophosphoric acid + ephedrine + iodine
There was a weight loss for the result. Would 110 degrees be okay?
2. Is it okay to calculate the capacity twice or three times for the mass production process and run the process? If so, how should we calculate the temperature and time of the reflux cooler?
3. I'm most curious about the process for number two. Simply put, if you start with six grams of ephedrine, if you put two or three times the dose in every process and manufacture it
I wonder what the temperature and time of the reflux cooler should be
4. The process of reflux cooler refers to the process in hypophosphoric acid + ephedrine + iodine

 

[GhostChemist]

The temperature can be 110 but longer in time
In this synthesis, phosphine is formed, therefore, an increase in the volume without ventilation hood is unsafe

 

[cicici]

Thank you for your answer
1. If you increase the volume, how much volume is appropriate?
2. If you increase the volume, how should you determine the time and temperature?
3. Why does it take longer than 100 degrees if you proceed to 110 degrees?
4.What is the appropriate temperature in your opinion?

 

[kafka82]

I am newbie - is there a video of this detailing the process? Also particualrly concerned about the best type equipment to procure fo rmagnetic heater and the reflux for example...

 

[@speedboysss]

https://erowid.org/archive/rhodium/worlock/meth.htmlI followed the recipe from here but failed what is the mistake where is the expert who can explain

 

[@speedboysss]

https://erowid.org/archive/rhodium/worlock/meth.htmlI made crystal meth with the Erwoid recipe but it failed. All the procedures were done correctly. What went wrong? Please correct me, where are the experts?

 

[Sagitarius A]

Kde je problém? poradim pokud budu znát odpověd. Klidně napis SZ