Methamphetamine From Ephedrine by Iodine and Red P

[Anarchy Labz]

Why did you use dcm, can this be done without dcm? Also isn't it a bit much to use 12g of I2 for 6g of ephedrine?

 

[InvincibleDealr]

Who can Reply me my question with certainty?
Assume i follow every step of this reaction in the video 100%, Except

1. For NAOH, I Use Caustic Soda. (will it decrease purity?)
2. Can i replace DCM with what OTC available solvents? aboveyou mentioned toluene, benzeneor pet. ether?
3. Petroleum Ether can be replaced with what? (at last stage)
4. For HCL Gassing: Will Epson Salt(MGSO4) + Battery Acid (H2SO4-28%) Produce good enough HCL gas ppm to produce the crystal? Or we need concentrated H2SO4 for crystal?

Lastly:
5. Anyone who tried this?
reaction left for 24 Hours between 60-80 Degrees?
6. sodium sulfate added to remove DCM then to sep. funnel. (other than sodium sulfate what other reagent can be used?)

By answering this. it may help future users stop asking all question i think

 

[GhostChemist]

@InvincibleDealr Don`t spam in all topics!

 

[Chemdog010297]

Can I do this synthesis at 140 Fahrenheit for 48 hours and get the same result ?

 

[GhostChemist]

We have not conducted these studies
Perhaps in the future we will receive these data and publish them
If you can carry out this synth at your parameters do it and present results

 

[Trgate]

24 hours is a really long time. We had to deal with bad smells and refrigeration. Is there a way to shorten it? Or would 12-18 hours be enough?

 

[GhostChemist]

We have not conducted these studies
Perhaps in the future we will receive these data and publish them

 

[Chemtrail]

The longer RXN reaction time

The more chemical conversion outcome


*It would be better to mix all the RXN ingredients and have sit for a long time (a week, month) and reflux with a non fancy heat source like a candle for 18-36 hours
THAN
Chuncking them in a heat -proof elymyer flask ($13 at Amazon) and use an electric oven or a blow torch 180 temp for an hour or so
*Didn't specify if it was 150 C or 220 F for that quick 180 temp *

 

[Trgate]

180 temp and an hour?

 

[thruster]

I did it by refluxing over 7-8h and rising temperature to 180 C at the end. Extraction was done from MTBE which worked very well. Lighter fluid/naphta also worked pretty good, better then toluene imo. Final yield and quality was very good.

 

[A person who has never be]

Is it most appropriate for me to use petroleum ether at 30-60 degrees?

 

[A person who has never be]

Is this method applicable to the synthesis of ephedrine extracted from Ephedra sinica?

 

[Chemtrail]

For a pound ~444gs of ephedra sinica you would be able to extract 4-14 grams of ephedrine alkaloids

Don't see why it would not work?

Conduct a trial experiment and post your lab results here

 

[Chemdog010297]

The idea should be be to chemically alter the ephedrine to Amine. So u should only need an equation that creates that synthesis. No more and no less. Idk it offhand. But all u would need to do is find it at its base equation and then u can change it from there depending on your knowledge. So if 1g iodine and .5g rp is enough for 3g ephedrine to be changed to amine (in example, not correct amount just example) u would need to react that synthesis until it is done completely, done completely meaning it doesn’t react anymore at all. However long it takes is however long it takes. From there u change the synthesis to better suit ur needs.

 

[LederLappenNiere90]

Hello BB Member's,

I have a question about a Pseudo Ephedrine source from Pharmacy shop's Tablet's.
It's named Grippostad Complex 500 mg oranges Aroma and 30 mg Pseudo Ephedrine per tablet.
Is it possible to extract them easy with a standard extraction showed here on the Forum
or is there another way to extract them ? Does it have hidden binder Material containing ?
For helpfully answers and idears how to get the good's out i where very Thankfull so !

 

[SoldadoDeDrogas]

Spend some time reading about it and answer it for yourself. You need to provide more details about the product in order to get the specific answers. Or you can figure it out yourself as you should be ...if you look up each individual ingredient/chemical and search their solubility properties. Find a solvent that will dissolve your ephedrine/pseudo and nothing else or the least amount. Then you wash the extracted E/PE after it was filtered and dried with something that won't dissolve the ephedrine but will wash away the other crap.
Some advice from the pros include, DRY EVERYTHING - NO WATER/MOISTURE! and NO HEAT! Water and heat are supposedly what activate the binder.

 

[LederLappenNiere90]

Sure i will,thank you for the fast reply, Soldado!
I'll get a packet of Grippostad Complex ASS Pseudoephedrine 20 tablets for €9.50, which would be 0.6 g of crude Pseudoephedrine.
There might be other ingredients listed on the packaging, and then I'll test each one individually for solubility!
Thanks for the tip about cold extraction without water; I'll take that into consideration!
I'm posting another link here for anyone interested in the same product.

https://www.docmorris.de/grippostad-complex-asspseudoephedrin

 

[Chemtrail]

Try to get Psudoephedrine as the only active ingredient.

Povidone and polyethylene glycol are the worst gaak ! Those make the extracting PSE more difficult

 

[LederLappenNiere90]

Do you know that this Preparation named Grippostad Complex ASS + Pseudoephedrine, contains exactly these active ingredients ?
Or, if these ingredients are present, should I give the product a wide berth and look for an alternative ?
Thanks for Response !

 

[Chemtrail]

Good

No , it is good to go

Povidone is just the worst gaak to separate. A simple alcohol extraction won't do. Swim has read bad news about povidone, but not fatal